Search results

Bonded composite patches are ideal for aircraft structural repair as they offer enhanced specific properties, case‐tailored performance and excellent corrosion resistance. Bonding minimizes induced stress concentrations unlike mechanical fastening, whilst it seals the interface between the substrate and the patch and reduces the risk of fretting fatigue that could occur in the contact zone. The purpose of this paper is to assess the electrochemical corrosion performance and the environmentally induced mechanical degradation of aerospace epoxy adhesives when carbon nanotubes (CNTs) are used as an additive to the neat epoxy adhesive.

The galvanic effect between aluminium substrates and either plain or CNT enhanced carbon fibre composites, was measured using a standard galvanic cell. Also, rest potential measurements and cyclic polarizations were carried out for each of the studied systems. The effect of the CNT introduction to a carbon fiber reinforced plastic (CFRP) on the adhesion efficiency, before and after salt‐spraying for 10, 20 and 30 days, was studied. The adhesion efficiency was evaluated by the single lap joint test.

The corrosion behaviour of the system is polymer matrix type dependent. CNT introduction to a CFRP may induce small scale localized degradation.

This paper fulfills an identified need to study how the shear strength and the response to galvanic corrosion are affected by epoxy resins modified by carbon nanotubes.

The purpose of this paper is to present the mechanical and morphological characterization of new multifunctional carbon fibre-reinforced composites (CFRCs) that are able to overcome two of the main drawbacks of aeronautical composite materials: reduced electrical conductivity and poor flame resistance. Multiwall carbon nanotubes and glycidyl POSS (GPOSS) were used to simultaneously enhance electrical conductivity and flame resistance. The effect of these two combined components on the mechanical and morphological properties of the manufactured CFRCs was analysed.

This paper describes the mechanical test results obtained for interlaminar shear strength, three-point bending, and tensile and fracture toughness in mode I tests. Carbon fibre-reinforced epoxy resin plates were manufactured in two series with blank resin and CNT+flame retardant GPOSS-enhanced resin.

The mechanical properties were decreased by no more than 10 per cent by combined influence of CNTs and GPOSS. Agglomerates of CNTs were observed using scanning electron microscopy. The agglomerates were large enough to be visible to the naked eye as black spots on the delaminated fracture surface. The decrease of the mechanical properties could be caused by these agglomerates or by a changed fibre volume content that was affected by the difficult infusion procedure due to high resin viscosity.

If we consider the benefit of CNTs as a nanofiller to increase electrical conductivity and the GPOSS as a component to increase the flame resistance of the resin, the decrease of strength seems to be insignificant.

A simple economic analysis has revealed that in order for wind energy to be a viable alternative, wind-turbines (convertors of wind energy into electrical energy) must be able to operate for at least 20 years, with only regular maintenance. However, wind-turbines built nowadays do not generally possess this level of reliability and durability. Specifically, due to the malfunction and failure of drive-trains/gear-boxes, many wind-turbines require major repairs after only three to five years in service. The paper aims to discuss these issues.

The subject of the present work is the so-called white etch cracking, one of the key processes responsible for the premature failure of gear-box roller-bearings. To address this problem, a multi-physics computational methodology is developed and used to analyze the problem of wind-turbine gear-box roller-bearing premature-failure. The main components of the proposed methodology include the analyses of: first, hydrogen dissolution and the accompanying grain-boundary embrittlement phenomena; second, hydrogen diffusion from the crack-wake into the adjacent unfractured material; third, the inter-granular fracture processes; and fourth, the kinematic and structural response of the bearing under service-loading conditions.

The results obtained clearly revealed the operation of the white-etch cracking phenomenon in wind-turbine gear-box roller-bearings and its dependence on the attendant loading and environmental conditions.

The present work attempts to make a contribution to the resolution of an important problem related to premature-failure and inferior reliability of wind-turbine gearboxes.

The purpose of this paper is to employ analytical and numerical techniques to generate modal displacement data of damaged beams containing very small crack-like surface flaws or slots and to use the data in the development of damage detection methodology. The detection method involves the use of double differentiation of the modal data for identification of the flaw location and magnitude.

The modal displacements of damaged beams are simulated analytically using the Bernoulli-Euler theory and numerically using the finite element method. The principle used in the analytical approach is based on changes in the transverse displacement due to the localized reduction of the flexural rigidity of the beam. Curvature analysis is employed to identify and locate the structural flaws from the modal data. The curvature mode shapes are calculated using a central difference approximation. The effects of random noise on the detectability of the structural flaws are also computed.

The analytical approach is much more robust in simulating modal displacement data for beams with crack-like surface flaws or slots than the finite element analysis (FEA) approach especially for crack-like surface flaws or slots of very small depths. The structural flaws are detectable in the presence of random noise of up to 5 per cent.

Simulating the effects of small crack-like surface flaws is important because it is essential to develop techniques to detect cracks at an early stage of their development. The FEA approach can only simulate the effects of crack-like surface flaws or slots with depth ratio greater than 10 per cent. On the other hand, the analytical approach using the Bernoulli-Euler theory can simulate the effects of crack-like surface flaws or slots with depth ratio as small as 2 per cent.

The main objective of this article is to develop a theoretical formulation for predicting the response of CNTs reinforced beam under multiple impactors with general boundary conditions, using first-order shear deformation beam theory.

The rule of mixtures is implemented to derive the material properties of the beam. The nonlinear Hertz contact law is applied for simulation between impactors and the surface of the beam. A combination of approaches includes energy method, Ritz method and generalized Lagrange equations are used to extract the matrix form of equations of motion. The time-domain solution is obtained using implementing the well-known Runge Kutta 4th order method.

After examining the accuracy of the present method, the effects of the number of impactors include one impactor, and three impactors in various CNTs volume fraction are studied for CNTs reinforced beam with clamped-clamped, clamped-free and simply supported boundary conditions under the low-velocity impact. The most important finding of this article is that contact force and beam indentation at the middle of the beam in the case of one impactor are greater than those reported in the case of three impactors.

This article fulfills an identified need to study how CNTs reinforced beam behaviour with general boundary conditions under multiple low-velocity impacts can be enabled.

The purpose of this paper is to present the concept of the author’s method of fatigue properties assessment of polymer composite structures, especially structures having nodes of concentrated force introduction (NCFI) using fatigue test data of coupons of similar composites and the ratio of their structural stress rate factors.

Basing on fatigue properties of pure composite shells coupons subjected to cyclic loads, and basing on the static strength difference between pure composite shells and shells having the structure affected by NCFI – (considered here as not only a manner of load introduction but also a kind of structural discontinuity), a method of relative fatigue properties reduction (RFPR) was developed. In the RFPR evaluation process, the author used the results of experiments on a special type of an NCFI named “a labyrinth non-adhesive node of concentrated force introduction” (LNA-NCFI) applied in certain composite gliders for fitting glider wings with the fuselage and also referred to design directives relating to primary structure of composite gliders, which are presented in the form of lightness factors linking stress with a structural mass.

The result of RFPR method application matched well with the results of fatigue tests of the LNA-NCFI type of a NCFI. The RFPR method may significantly facilitate the estimation of fatigue life of a structure with a structural discontinuity or an NCFI.

The RFPR method may significantly facilitate the estimation of fatigue life of a structure with a structural discontinuity or an NCFI.

The paper presents a proposal of a novel simplified method for fatigue life estimation of composite structures having a kind of structural discontinuity or an NCFI.

The purpose of this paper is to introduce a new numerical approach for studying a cantilever bar having a transverse crack. The crack is modeled by an elastic longitudinal spring with a stiffness K according to Castiglione’s theorem.

The bar is excited by different longitudinal impulse forces. The considered problem based on the differential equation of motion is solved by the method of characteristics (MOC) after splitting the second-order motion equation into two first-order equivalent equations.

In this study, effects of the crack size and crack’s position on the reflected waves from the crack are investigated. The results indicate that the presence of the crack in the cantilever bar generates additional waves caused by the reflection of the incident wave by the crack.

A numerical approach developed in this paper is used for detecting the extent of the damage in cracked bars by the measurement of the difference between the dynamic response of an uncracked bar and a cracked bar.

The purpose of this study is to investigate the results of reinforcing fibre metal laminates with glass fibres under low-cycle fatigue conditions in a limited number of cycles.

The tests were carried out on open-hole rectangular specimens loaded in tension-tension at high load ranges of 80 and 85 per cent of maximum force determined in static test, correspondingly. The number of cycles for destruction has been determined experimentally.

By means of microscopic observations, it was possible to determine the moment of crack initiation and their growth rate. Furthermore, it was possible to identify the impact of reinforcing fibre orientation in composite layers, material creating the metal layers, on fatigue life and on nature of crack propagation.

This work validates the possibility of increasing the resistance of fibre metal laminates to low-cycle fatigue by modifying the structure of the laminate.

The resistance of fibre metal laminates on low-cycle fatigue is not widely described and the phenomena occurring during degradation are poorly understood.

Gives a bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore aims to give the reader an encyclopaedic view on the subject. The bibliography at the end of the paper contains 2,025 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1992‐1995.

The purpose of this paper is the development of a multiscale model which simulates the effect of the dispersion, the waviness, the interphase geometry as well as the agglomerations of multi-walled carbon nanotubes (MWCNTs) on the Young’s modulus of a polymer filled with 0.4 Vol.% MWCNTs.

For the determination of the homogenized elastic properties of the hybrid material representative unit cells (RUCs) have been used. The predicted homogenized elastic properties were used for the prediction of the Young’s modulus of the filled material by simulating a finite element (FE) model of a tensile specimen. Moreover, the model has been validated by comparing the predicted values of the numerical analysis with experimental tensile results.

As the MWCNT agglomerates increase, the results showed a remarkable decrease of the Young’s modulus regarding the polymer filled with aligned MWCNTs while only slight differences on the Young’s modulus have been found in the case of randomly oriented MWCNTs. This might be attributed to the low concentration of the MWCNTs (0.4 Vol.%) into the polymer. For low MWCNTs concentrations, the interphase seems to have negligible effect on the Young’s modulus. Furthermore, as the MWCNTs waviness increases, a remarkable decrease of the Young’s modulus of the polymer filled with aligned MWCNTs is observed. In the case that MWCNTs are randomly dispersed into the polymer, both numerical and experimental results have been found to be consistent regarding the Young’s modulus.

The methodology used can be adopted by any system containing nanofillers.

Although several studies on the effect of the MWCNTs distribution on the Young’s modulus have been conducted, limited results exist by using a more realistic RUC including a periodic geometry of more than 20 MWCNTs with random orientation and a more realistic waviness of MWCNTs with aspect ratio exceeding 150.